ronde poteau de bois de pin traité poteau en bois paddock clôture

Wooden round pine posts (without pointed tip) 

from Northern Europe and impregnated in autoclave

AVAILABLE MEASURES

---------------------------------------

Post diameter 8cm – H150cm

Post diameter 8cm – H200cm

---------------------------------------

Post diameter 10cm – H150cm

Post diameter 10cm – H200cm

  * Choose the height from the drop-down menu located at the top, under the title of the product.

To buy wooden post accessories click here 

• piquet en bois  

The rounded wooden posts are primarily used for fences and in agriculture as support posts for vineyards and orchards.

Our rounded pine posts come from Northern Europe, where plants grow slower because of the harsh climate, making the wood grain more resistant and suitable for processing.

All the rounded posts are impregnated in autoclave with a saline preservative and subsequently brought to a pressure of 12 atmospheres.

The impregnation process makes the wood more resistant to weather and pests, preventing the onset of mould and mildew.

This method attains and protects, in depth, the fibre of the wood, unlike other treatments that are limited to a superficial protection.

Uses:  Wood is a building material widely used in modern construction as it is natural and ecological. The rounded wooden posts are used for the construction of fences and used in agriculture as support posts for vineyards and orchards.

Thanks to the various measurements available, from different diameters and from different processes, the rounded posts allow the creation of structures for outside, palisade fences, bicycle paths, fences for horses, civilian and sporting precincts, walkways and borders, etc.

The rounded posts are greatly used in environmental architecture and landscape.

Impregnation process:

Our poles are treated with a wood preservative Tanalith E and dye Tanatone vacuum-pressure-vacuum (SPS) in an autoclave.

The wood preservative Tanalith E (produced in the Uk and the market leader) has a soluble and resistant formula, containing copper carbonate and organic biocides, which protects the wood for a long period.

  Productive process:

Before sending the pallet of material into the autoclave, dividers are put for each layer of material. After which the pallet, with a special trolley, is loaded into the autoclave, the tank is closed tightly and initial vacuum is created. Thanks to this the wood's pores are opened. The vacuum is maintained for a certain time.

After, the autoclave is filled with a liquid substance prepared according to protocol and with a hydraulic pressure up to 12 atmospheres. The material is impregnated with an aqueous solution of an antiseptic preservative TANALITH® E or wood dye TANATONE®  and an additive TANAGARD (the additional protection against fungus and parasites).

Subsequently, the autoclave is depressurized, the solution of preservative and dye is discharged from the autoclave to the storage tank and it creates the final vacuum, which removes the excess of the solution from the wood. The vacuum is removed and the autoclave is depressurized. The technological process is completed.

As a result of impregnation, the components of antiseptic preservative and dye (or only preservative) are fixed so deeply into the wood structure that it becomes almost impossible to remove. The dried wood is protected from UV rays on a separate platform.

After impregnation S-P-S the pinewood receives hardwood quality, achieving greater resistance thanks to copper microparticles. The selected chemical elements protect the wood from insects, fungus, moisture and UV rays. Without contact with soil, this wood is virtually indestructible. In contact with soil and water, the wood will survive for at least 10 years.

N.B. WHEN YOU BUY MORE PRODUCTS FROM OUR EBAY STORE 

YOU PAY A SINGLE DELIVERY FIXED PRICE!   TAKE ADVANTAGE !!!

To buy other ITALFROM products click here 

• Export français  

WE ARE AVAILABLE TO OFFER FREE ESTIMATES ACCORDING TO YOUR NEEDS:

Galvanized modular panel fencing, wire mesh fencing roll complete with posts, 

diagonal posts, wire tension, wire for tying and tensioners.

SO DO NOT HESITATE TO CONTACT US:

CONTACT

skype: export italfrom

email:  ebay@italfrom.com

tel:  0039 0825 818686

LAYING OF WIRE MESH FENCING

For long lasting and easy installation of a wire mesh fence, you should carefully read this page.

To follow the first figure below, you will need: the starting post with a single diagonal post for reinforcement (A); corner post, with 2 diagonal posts at 90° (B); intermediate post, (C1); and finally a reinforced post with 2 diagonal posts (C2).  The posts of reinforcement are required every 25 metres for linear fencing.

_____________________________________

Fences with wire mesh rolls, can come in two different types: with posts cemented or posts fixed into the soil.

Look at the picture below :

1)      In the first figure, it shows a wall or concrete cube, for which the height of the post should be the same height as the mesh plus 25cm ("h" + 25cm).

2)      In the second figure, posts fixed into the soil, the post should be the same height as the mesh plus 50cm ("h" + 50cm).

__________________________________________

Depending on the length of the perimeter, the number of the posts and the necessary accessories must be determined for installation.  The posts should be placed at a distance, preferably every 2 metres.

You will then need to measure the sides of the fencing and carefully count the posts needed.

  _________________________________________

VARIOUS STEPS OF THE IMPLEMENTATION OF THE FENCE:

1)  Installation of posts and diagonal posts. 

1)      Decide the type of fence to be installed (fixed into the soil or cemented).

2)      Outline well the area of the fence with a rope like a bricklayer’s, with which it should be marked in a straight line to the border

3)      Once you have outlined well the area of fencing, it is necessary, according to your needs, to set the frame of the fence (in the soil or in the cement), as well as the posts and diagonal posts.

4)      It is better to start laying with the corner posts.

If you want to fix the posts with cubes of cement mortar , you should dig a hole of about 25x25x25cm.  After filling the hole with cement mortar, the post should be driven in until it touches the bottom, held in alignment with the placed ropes and checked with a spirit level.

If however, the posts are to be fixed into the soil, the hole should be about 50cm

2)  INSTALLATION OF TENSION WIRE AND RESPECTIVE TENSIONERS

Once you have constituted the frame of your fence with the positioning of the posts and diagonal posts, the next step is essential.  It is to give robustness to the fence, by passing the tension wire through the holes on each post and tying them to the respective tensioner.

Once you have applied the tensioner to the respective tension wire (preferably at a distance of about 15cm from the post) with the help of a pincer or respective key, pass the tension wire into the tensioner which will allow you to pull the tension wire to the right point, to strengthen your fence to the maximum.

3)   INSTALLATION AND SECURING OF THE MESH

The last step that remains, to see your work completed, is the installation of the mesh, which is generally done by starting at the starting post and by tying the mesh with the binding wire to the post.

At this point you can proceed with the unrolling of the mesh, along all the posts you have installed, by tying the mesh to the tension wire and to the respective posts.

Join the last part of the fence, making sure that the mesh is tight on every point, tying it like you did at the first post.

At this point you can see, with a lot of satisfaction, your completed work .

IF YOU WOULD LIKE AN INVOICE, PLEASE INFORM US, BY MESSAGE, AT THE TIME OF PURCHASING, 

OTHERWISE IT WILL BE GIVEN IN THE FORM OF A RECEIPT.  

FOR ANY PROBLEMS, BEFORE LEAVING A NEGATIVE OR NEUTRAL

 FEEDBACK, PLEASE CONTACT US AND WE WILL RESOLVE

THE PROBLEM IMMEDIATELY

DISPATCHED 24/48 HOURS FROM ORDER