Parcel include:
4 Axis for medium size Router Mill Plasma or Laser
1. 5 axis breakout board
Description:
25-pin parallel port control is defined as follows:
DB25 control pin (PIN) | The pin of the drive board | Comment
|
1 | STEPB | B(Fifth axis)pulse signal |
2 | STEPX | X(First axis) pulse signal |
3 | DIRX | X(First axis) direction of the signal |
4 | STEPY | Y(Secondaxis)pulse signal |
5 | DIRY | Y(Second axis)direction of the signal |
6 | STEPZ | Z(Third axis) pulse signal |
7 | DIRZ | Z(Third axis) direction of the signal |
8 | STEPA | A(Fourth axis) pulse signal |
9 | DIRA | A(Fourth axis) direction of the signal |
10 | LIMIT-1 | Limit input interface 1 |
11 | LIMIT-2 | Limit input interface 2 |
12 | LIMIT-3 | Limit input interface 3 |
13 | LIMIT-4 | Limit input interface 4 |
14 | DIRB | B(Fifth axis) direction of the signal |
15 | Vacant |
|
16 | RLY | Relay control |
17 | EN | All axis enable |
18-25 | GND | GND |
Remark:this 5 axis breakout board can connction with many driver type as a CNC 3/4/5 axis driver controller kit,pls if you intresting pls contact us!
2. CW5045 high microstep stepper motor driver
Description:
Switch Choice: (ON=0,OFF=1)
1.Microstepping choice:
SW5 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 |
SW6 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
SW7 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 | 0 | 0 |
SW8 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | 0 | 1 | 1 |
Micro | 1/2 | 1/4 | 1/8 | 1/16 | 1/32 | 1/64 | 1/128 | 1/256 | 1/5 | 1/10 | 1/25 | 1/50 | 1/125 | 1/250 |
2.Current choice:
SW1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
SW2 | 0 | 0 | 1 | 1 | 0 | 0 | 1 | 1 |
SW3 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 |
Current(A) | 1.3 | 1.8 | 2.3 | 2.7 | 3.2 | 3.7 | 4.2 | 4.5 |
3.Full current or half current choice: SW4:0=Full current; 1=half current
We also can offer customer NEMA17-23 stepper motors,so if you need pls contact us.
Application Notice:
2. Stepper Motor
General Specification:
Step angle accuracy:+ - 5%(full step,not load)
Resistance accuracy: + - 10%
Inductance accuracy:+ - 20%
Temperature rise: 80deg Max(rated current,2 phase on)
Ambient temperature ----------—20deg ---- +50deg
Insulation resistance:100ohm Min,500VDC
Insultion Strength--------500VAC for one minute
Datasheet(23HS2430,Front shaft 8mm dia and 21mm length,back shaft 8mm dia and 11mm length,425 oz-in or 28kg.cm holding torque)
Note:if you need single shaft pls contact us,we have in stock.
Motor lead wires:
Red: A+
Green: A-
Yellow: B+
Blue: B-
3.Switching power supply
400W,Input:100-120VAC or 200-240VAC,50/60Hz,Output:36v/9.7 A,single output switching power supply
We care about our valued customers,and will always try to help you,hope to establish long business with you.
Pls give us the opportunity to resolve any problem, we understand the concerns and frustrations you might have,and will try our best to resolve the issues.
Pls contact us by ebay message or email before leaving any negative feedback or opening any cases on the site,we will help you to resolve the problem