describe:
DCF receiver module with DCF antenna tuned to time signal transmitter DCF77 (Frankfurt 77.5 kHz). The antenna induction signal is sent to the IC for amplification, demodulation, and then identified by the MCU, so that the date and time of the timing center can be completely consistent.
Below you will find important setup and circuit diagrams.
Technical Specifications
DCF---77.5KHZ single frequency specification:
Product number: DCF-1060N-03A
RCCM category: DCF/77.5KHz single frequency module
PCB size: 25.0x11.5x1.0mm/FR4
Antenna size: AR10x60mm/High Q
Nominal frequency: 77.5KHz±300Hz
Sensitivity: 27±2dB
Receiving IC: CME6005
JJY-40/60KHZ dual frequency specification
Product number: JJY-1060N-MAS
RCCM category: JJY/40+60KHz dual frequency module
PCB size: 22.0x13.5x1.0mm/FR4
Antenna size: AR10x60mm/High Q
Nominal frequency: 40/60KHz±300Hz
Sensitivity: 40/60K:30/28±2dB
Receiving IC: MAS6181B
• Operating voltage: 1.1...3.3 V
• Current consumption: 85 µA max
• Receiving frequency: 77.5 KHz
• Board size (without antenna) LxWxH: 22x13.5x1 mm
• Antenna quality: LxØ: 60x10mm
• Scope of delivery: 1 piece
⇒ DCF receiver module with antenna
• connect:
⇒ Ground = Pin G
⇒ Operating Voltage = Pin V
⇒ data = pin T
⇒ Power On/Off = Pin P1
⇒ 40/60K frequency selection = SEL
⇒AGC(Note 4: Optional Control for AGC On/Hold
AON control pin has internal pull up which turns AGC circuit on all the time if AON pin is left unconnected.
Optionally AON control can be used to hold and release AGC circuit. Stepper motor drive of analog clock or
watch can produce disturbing amount of noise which can shift the input amplifier gain to non optimal level. This
can be avoided by controlling AGC hold (AON=VSS) during stepper motor drive periods and releasing AGC
(AON=VDD) when motors are not driven. The AGC should be in hold only during disturbances and kept on other
time released since due to leakage the AGC can still change slowly when in hold.)
• Important note:
⇒ PIN P1 is an on/off switch and must be set to logic low.
Note: Single-frequency modules cannot be switched between different frequencies of DCF/WVB/HBG/BPC, JJY dual-frequency modules can be switched between 40K/60K two frequencies, to make a certain single-frequency module, only can receive signals in this frequency band.
Package Included:
1*Receiver module
Payment
Payment must be made within 5 days. Please list your special requests (color, packages, value of declaration, etc.) in the Paypal notes section when you make payment.
International buyers--PLEASE CAREFULLY NOTE:
a) Import duties, taxes and charges are not included in the item price or shipping and handling. These charges are the buyer’s responsibility.
b) Please check with your country’s customs office to determine what these additional costs will be prior to bidding/buying.
Orders processed within 24-48 hours of payment verification.
We only ship to confirmed Paypal addresses. Your Order address must match your Shipping address.
Please kindly note that we don't provide combined shipping because the shipping fee is calculated by weight. Also, the each additional item means the exact same one, with the same color and size.
Service transit time is provided by the carrier. It takes about 10-15 working days to France;about 10-30 working days to other countries. Transit times may be a little delayed during holiday season.
Contact us
Nous nous efforçons de satisfaire votre clientèle à 100%! Les commentaires positifs sont très importants pour nous. Si vous avez des questions, n'hésitez pas à nous contacter via "Posez une question au vendeur", nous répondrons votre courrier électronique dans les 24 heures ouvrables.