2 / 4 Way Traffic Light Control Circuit For Model Railway, N / OO / HO Gauge

2 / 4 Way Traffic Light Control Circuit For Model Railway All Gauges

The circuit is powered via DC supply 9v - 25v. We also sell power supply circuits which give a single DC output and a multi DC voltage output.

We also supply this circuit with working N Gauge traffic lights.

Your browser does not support the video tag.

We now also stock various power supply units for model rail, Our power supply units can connect directly to you controller and give you various of other power options. These units can take AC/DC 16-24 volt inputs and produce a stable fixed DC voltage output of 6v 9, 12, and 15v.

Full product datasheets can be found at http://www.modellingelectronics.co.uk/datasheets/?f=2&key=102-001

2 / 4 Way Traffic Light Control Circuit Wiring Instructions

The circuit once wired in this manor will give an output as below.

To wire the traffic light control circuit you do need to connect resistors to the leds. We recommend using 330ohm resistors for the leds before connecting to the circuit. The circuit is powered via a DC supply 9v – 25v

please take care when wiring the led's to the circuit and please make sure you have disconnected the power.

Terminal output 1 is the negative supply of the led's for the following lights. Green East and West, Red North and South and Yellow East and West. Terminal output 2 is the negative supply of the led's for the following lights. Green North and South, Red East and West and Yellow North and South. Terminal output 3 is the positive supply for Green led's East and West. Terminal output 4 is the positive supply for Red led's North and South. Terminal output 5 is the positive supply for Yellow led's East and West. Terminal output 6 is the positive supply for Green led's North and South. Terminal output 7 is the positive supply for Red led's East and West. Terminal output 8 is the positive supply for Yellow led's North and South.

A wire loop is required between terminals 5 and 8

The above wires the traffic light control circuit for 4 way traffic, If only two way traffic is required simply remove the led's for East and West, this will now allow traffic lights for road works etc.

Input voltage should be 9v - 25v  DC only.

Terms & Conditions

Due to the sensitivity of these circuits and components (Due to damage incurred by incorrect wiring) we can only accept returns and issue a refund once our engineers have fully tested and confirm the component or circuit is fully working. We test each circuit before it leaves our factory, which it is then verified by a senior team member and signed off. Please make sure you read our website for product data sheets and wiring instructions before you connect your component or circuit.

Delivery & Returns

Delivery

Delivery to UK addresses will normally be despatched within one working day. In most cases we can get your order out the same working day via the last post. We always hold enough stock to meet all orders, and all stock is held within our UK outlet.

 

Payment

Online orders via eBay can only be paid for via PayPal, with PayPal you can use your debit/credit card or your PayPal ballance.

Returns

Unwanted Goods: Please contact us within 28 days of purchase to obtain a returns number, this must be clearly marked on any returns note. Goods must be returned to us at your own cost and in the same condition that they were received, including packaging, manuals and all accessories. Goods returned as unwanted or incorrectly ordered will be subject to a restocking charge of 20% of the goods value with a minimum charge of £6.00.

Incorrect/missing/faulty: Should you need to contact us with regards to the contents of your order, whether you have missing, incorrect or faulty goods, please contact us using the below methods.

Modelling Electronics 68 High Park Road Southport Merseyside PR9 7QL Tel:0800 0096656 Fax:01704 201348

Technical enquiries: support@modellingelectronics.co.uk Sales enquiries: sales@modellingelectronics.co.uk

• Condition: Neuf
• Brand: Modelling Electronics
• Power Supply: DC
• Country/Region of Manufacture: United Kingdom
• Scale (Gauge): OO, N, HO, Z
• Product Type: Train Parts & Accessories
• Sub-Type: Electronics
• Assembly: Pre-Assembled
• Method of Power: 9v DC

Voir Plus